Trades
Set it up for the work you do.
Kredna is the same app for every trade. Your trade shows up in your library and in what the scope assistant looks for.
Starter packs are included for drywall and metal framing, painting, electrical, and structural and miscellaneous steel. For every other trade, build your items once. Then make it yours: your assemblies, your crews, your prices.
Site
Demolition
Removals by area and length, saw cuts, hauls and protection, matched to the demolition keynotes.
Excavation and earthwork
Stripping, cut and fill by area and depth, footing excavation, stone base and erosion control.
Site utilities
Storm, sanitary and water pipe with trench and bedding, structures, hydrants, valves and taps.
Paving and striping
Asphalt by area with its base and tonnage, flatwork, curb, striping, symbols and signs.
Landscaping and irrigation
Plants by count and size, sod, seed, mulch and soil by area and depth, and irrigation.
Fencing
Fence by type and height with posts at your spacing, gates by width, bollards and temporary fence.
Structure
Concrete
Footings, walls and slabs in cubic yards, with forms, vapor retarder and rebar as parts of your own items.
Masonry
Block walls by length and height with block, joint reinforcing and mortar as parts, plus veneer.
Structural steel
Members by size with their weight per foot, plate, connections and deck, priced with Shop and Field labor.
Miscellaneous metals
Railings by the run, stairs by the riser, lintels, embeds, ladders and bollards, each with its parts.
Framing and rough carpentry
Stud walls with studs and plates, joists by spacing, sheathing in sheets, trusses, blocking and hardware.
Envelope
Roofing
Roof areas by system in squares, flashings and sheet metal by the foot, curbs and penetrations counted.
Waterproofing and sealants
Below-grade walls by the height waterproofed, air barrier by area, sealant joints by type and length.
Insulation
Batts by wall type and rating, rigid board by the board, spray foam by thickness, safing by the foot.
Siding and cladding
Siding and panels by area from the elevations, trim and flashing by the foot, furring at your spacing.
Glass and glazing
Storefront and curtain wall by area and perimeter, windows counted by size, entrances and interior glass.
Interiors
Doors, frames and hardware
Openings counted on the plans, each carrying its door, frame and hardware set as parts.
Finish carpentry and millwork
Casework and countertops from the interior elevations, trim by length and paneling by area.
Drywall and metal framing
Walls drawn by type, with studs, track, board, screws, tape, compound and Frame, Hang, Tape and Finish labor as parts.
Acoustical ceilings
Lay-in ceilings drawn by area, with tile, grid, wall angle and hanger wire worked out from each one.
Flooring
Carpet by the square yard, resilient and hard floors by the square foot, base by the foot.
Tile
Floor and wall tile by area with waste, setting material and grout by the bag, trim by length.
Painting
Walls, ceilings, doors and trim, with gallons from the area, the coats and your products' spread rates.
Specialties and accessories
Toilet partitions, accessories, extinguisher cabinets, lockers and signs counted from the plans.
Mechanical, electrical and plumbing
Fire sprinklers
Heads counted by type, mains and branch lines by size and length with hangers, risers and valves counted.
Plumbing
Fixtures counted against the fixture schedule, water, waste, vent and gas pipe by size and length.
HVAC and sheet metal
Equipment by tag, duct by size with the sheet worked out, air devices by type, refrigerant and condensate pipe.
Electrical
Devices and fixtures counted, EMT, MC and wire by length, with the electrical starter pack's assemblies and Rough-in and Trim labor.
Low voltage
Data outlets and devices counted from the legend, cable worked out from the drops, tray and J-hooks by the foot.
Don't see your trade?
Build its items once in your library and write what the scope assistant should look for. Every job uses them from then on.