Looks and labels: how takeoffs are drawn
Set the color, line, fill, hatch, count symbol and label of an item or of one takeoff, drag labels where you want them, and set your company's defaults.
A look is how a takeoff is drawn and what its label says. A look never changes what is measured or priced: a hidden takeoff still counts, and a line drawn 6 in wide measures the same as a thin one.
Three levels
Looks come from three places, and the nearest one wins, value by value:
- Your company's defaults, in Settings › Company › Takeoff looks.
- The item's look: every takeoff of the item follows it.
- One takeoff's own look, for a piece you want drawn differently.
A level only sets what you change. Everything else follows the level above, and keeps following it when that level changes.
Open the Look panel
Properties, under the job tree, has two tabs: Properties and Look.
- Select one or more takeoffs to set their own look. A change sets every selected takeoff.
- With nothing selected, hold an item (Space) or click it in the job tree to set the item's look in this job.
- Right-click a takeoff and choose Look… to go straight there.
The sample at the top is drawn the same way as the sheet, so you see each change before you look up. The sheet changes at once too, and every change is one undo step.
A value in blue is set at this level. Click the × beside it to take it off, so it follows the level above again. A value that isn't set here says where it comes from: item, company or standard.
All takeoffs
- Color: click a swatch, or the last one for any color.
- Opacity: how solid the whole takeoff draws.
- On the drawing: clear Show to hide it. A hidden takeoff is still measured and priced.
Lines
- Width: in pt it is the same on screen at any zoom. In in, ft, mm or m it is that wide on the drawing, at the sheet's scale, so a 6 in curb draws 6 in wide.
- Style: Solid, Dashed, Dotted or Dash-dot.
- Side: Center, Left or Right of the line you clicked, looking the way you drew it. Use it for a wide line you traced along one face.
- Corner marks: a small square on each point you clicked, and its size.
- Ends: None, Tick, Arrow or Dot at the two ends of a run.
If the sheet has no scale, a real width can't be worked out. The line draws at a fixed width and the panel says why. Set the scale and it draws true.
Areas
- Fill: None, Solid tint or Hatch.
- Fill opacity: how strong the tint is.
- Pattern: diagonal (both ways, and wide), crosshatch, horizontal, vertical, dashes, grid, dots, brick, tile, concrete, earth and insulation.
- Hatch scale: how long one unit of the pattern is on the drawing. The hatch keeps that size at any zoom. Zoomed out too far to read, it draws as a tint.
- Hatch color: the item's color until you give it its own.
- Outline: on or off. Its width and style are the line's.
Counts
- Symbol: circle, square, triangle, diamond, cross, check, star, hexagon, pentagon, plus, X, filled dot, ring, arrow, flag, or a letter in a circle. Pick the letter symbol and type the letter.
- Size: in pt, or a real size on the drawing.
- Rotation: turns every marker.
- Filled: clear it to draw the outline only.
What the label says
Under Label, Says shows the label as parts in order. Click + Add part to add one:
- Takeoff name, Item name and Folder name.
- Quantity and Unit. A unit added after a quantity sits right beside it, as in "124 LF".
- Length, Area, Perimeter and Count.
- Any of the item's properties, such as Height or WallType. A takeoff's own value is used when it has one.
- Text… for your own words.
Click a part to move it earlier or later, or to remove it. Separator sets what goes between parts: a dot, a space, a comma, a dash, a bar, a colon or a new line.
A part with nothing to say is left out, along with its separator. A takeoff with no name reads "124 LF", not " · 124 LF". A quantity that isn't known yet reads "—".
Typed shows the same label as text, for when you would rather type it. A name in square brackets is filled in for each takeoff, such as [Qty] or [Height].
How the label looks
- Show: this label on or off.
- Size: Small, Normal, Large, or a number.
- Text color: the item's color until you give it its own.
- Background: None, White box or Tinted box, with or without a Border.
- Leader: a thin line from a label you moved back to its piece.
Move a label
Drag a label on the sheet. It stays where you put it, with a leader back to its piece, and it goes with the piece when you move or copy it. To put it back, right-click the takeoff and choose Put label back on the piece, or set Sits to On the piece in the Look panel.
All labels at once
Labels on the ribbon (Shift+L) turns every label on and off. The small arrow beside it has two choices for this computer:
- Show labels for: Every takeoff, The held item or The selection.
- Label size on this computer: make every label bigger or smaller, for a large or a small monitor.
Labels never pile up. Where two would sit on top of each other, one is drawn: the selection's first, then labels you placed, then the rest. Zoom in to see the others.
Right-click a takeoff
- Look…: open the Look panel.
- Hide label or Show label.
- Put label back on the piece.
- Flip line side (F, with a run selected).
- Bring to front and Send to back.
- Hide on the drawing (still measured). To bring hidden takeoffs back, right-click the empty sheet and choose Show hidden takeoffs.
- Copy look and Paste look: paste goes onto everything selected, as one step.
Back to the item's look, in the Look panel, takes off everything a takeoff has of its own.
Save an item's look to the library
Changing an item's look in a job changes that job only. If the item came from the library, Save look to library in the Look panel gives the library item the same look, so new copies start with it. Its parts and prices are not touched.
You can also set a look in the item editor: open Look and label at the bottom of its properties.
Company defaults
Settings › Company › Takeoff looks sets what an item draws with when it sets nothing of its own: what the label says, its size and background, the line width, the fill opacity, and the count symbol and its size. Every item that hasn't set its own follows them, in every job.
If something goes wrong
- A takeoff vanished: it may be hidden. Right-click the empty sheet and choose Show hidden takeoffs.
- A wide line draws thin: the sheet has no scale, or the width is in pt. Set the scale, or pick a real unit.
- A label is missing: check Labels on the ribbon and Show labels for. A label is also left out where another already sits, and on a piece too small on screen to tell apart.
- F starts Click fill: with no run selected, F is Click fill. Select the run first.
Something here doesn't match what you see in the app? Tell us at support@kredna.com.